Chosen Solution Hi friends, In an attempt to replace my iPhone 7 battery, I tore what I have gathered to be the ribbon cable responsible for touch ID (when iPhone is open like a book, the bottom cable closest to the home-button-end of the phone that falls flesh with the circuit board on the front half of the phone). I understand that in order to replace this cable the entire backlight needs to be replaced....
Chosen Solution I don’t have an iopenr to soften the seal of my phone but I do have a flattop stove that uses electricity. Is this okay to use? Defiantly not. You shouldn’t need any heat on the 7 plus unless it is extremely cold. If you need to use heat and haven’t got an iOpener you can use a hair drier on the lowest setting.
Chosen Solution Hello, I have found similar questions to mine, most offering to make a fusion drive by adding an SSD blade. This is not a good option for me. My internal HDD is failing in my iMac 27" (late 2013) and I am using an external Samsung 850 EVO 1TB SSD currently. I would like to remove the HDD and put the SSD inside. I plan to buy the kit for replacement and a 2....
Chosen Solution Is there another connection on the motherboard for a secondary sata drive? The teardown indicates it is possible to fit one but is it possible to hook one up? There is plenty of room for another hard drive and room to thread another SATA hard drive-to-logic board cable through to an empty connector spot on the logic board. So yes, it should be easy to install a second hard drive....
Chosen Solution The screen on my lap top is cracked - is there any way I can replace it myself? Yes, its possible. First is the cover glass broken and/or the LCD its self? If the LCD is gone the best way is just replace the complete lid assembly. Follow this IFIXIT guide: MacBook Pro 13" Unibody Mid 2012 Display Replacement. While the assembly is a bit more expensive than the LCD panel alone its a lot less work....
Chosen Solution my charger does not fit into the docking connecter i figured out that you need to stick a needle in to the docking connector to take out the lint that is inside of it For the Nano 7th Generation you need a: Apple Lightning Authorized White iPhone, iPad, iPod USB Charge and Sync Cable End 1: USB Male Plug End 2: Apple Male Lightning Connector
Chosen Solution Hi my hoverboard has the three prong charging port and the one of the prongs fell off.Is there any alternate way to charge it with just two prongs? You will most likely have to replace the charging port. If This is the right charging port than it shouldn’t be that hard or expensive to replace. Charging port I charge my swagway from either 2015 or 2016 with just two prongs; as long as you have two, it should still charge fine, only slower....
Chosen Solution I recently picked up this Vostro 200 as a scrap system. Since I am testing it as a candidate for a future guide I want to test it and avoid a bad system partway through since I will never get the time back and it will delay things worse then not having hardware. I was mainly testing it to find any serious issues that will be a total gotcha....
Chosen Solution My washer shows both error messages and will not finish through the spin cycle. I took off the front and emptied the drain with no luck elisha, the SUD error on these machines is usually displayed when the motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. This could be caused by a bad pump, an extra heavy load, excessive detergent, or excessive suds....
Chosen Solution Hi guys. Need help my MacBook Pro keeps rebooting with a kernel panic. I have tried as much as I can boot in safe mode repairing disk in disk utility from the recovery partition. I did try to reinstall the OS but it kept kernel panicking when it was downloading. I have managed to copy & paste the kernel panic report into a note so I can post it if anyone knows how to decipher it....
Chosen Solution I bought this laptop used a year ago, and like a month ago I started facing issues. Trackpad sometimes was not clicking, keyboard sometimes did not respond - it was because of trackpad flex cable, and I used to fix it by disassembling my laptop and moving that flex cable a little. I bought a replacement, and was disassembling my laptop almost each day while I was waiting for the delivery....
Chosen Solution Hi Guys. I have am IPhone 6 plus with touch problem with grey bars. I changed touch Ic with M1 jumper. The touch dont work. I find a same problem ( on ifixit forum) and verify have FL2034 short to ground. (because the M1 pad near to GND) I change IC, carefully.. Now there is not short in any component, but touch dont work again. My question is, Its better to change fl2024, because i turned on the phone with this short?...
Chosen Solution relating to this, if i put the logic board of my old iphone 4 8gb into a new iphone 4 8gb, would it boot up my phone in the exact same way, and basically be the same phone? I agree with jessabethany here it would be cheaper fixing your phone than trying to thrasher the guts to a new phone. Besides, I think you’ll find this will be harder that messing up the screen....
Chosen Solution Does anyone know where I can get a replacement motherboard for a 2009 MacBook Pro. I don’t remember the ghz I believe it’s the lowest available 2.2? Mine was fried after a water incident. Apple MacBook Pro “Core 2 Duo” 2.26 13" (SD/FW) Specs Identifiers: Mid-2009 13" - MB990LL/A - MacBookPro5,5 - A1278 - 2326* The logic board is Apple part # 661-5230 for the 2.26 GHz 661-5231 for the 2....
Chosen Solution I’ve got a A1181 1.83. I was having some kernel panic shutdowns for a week or so, and now when I push the power button, only the fan powers up (at least, that’s the only noise I hear). There’s a faint, very brief flash on the screen, a bzzt bzzt sound (I’m not sure where this sound originates), then the fan comes on. Battery charges, green light on charger is on....
Chosen Solution Hello, I have macbook (white) 4,1 early 2008 (160gb hd). One day I tried to start the mac up but it does’t react at all. there is no lights at all, even no on the magsafe plug, also there is no sound came from the mac - absolutely nothing. I tried the magsafe on another mac and it working good. i’m not using the battery a while since it swollen, so i used this mac as a desktop mac, it always connected to power supply while in use....
Chosen Solution I need to know if I could use a 2009 A1278 macbook pro 13" unibody top case on my macbook pro 13" early 2011. A1278 will this be compatible? thank you Lynn No - a lot of revisions occurred in the intervening years. If this answer is acceptable please remember to return and mark it.
Chosen Solution Through a series of unlucky events in ended up resting my macbook on the car on my way inside. I fell asleep lastnight and as I woke I came outside for some fresh air only to be greeted by my macbook. It did not appear to be wet and the lid was closed. I immediately took it inside and tried to power it on but I got nothing. I plugged in the charger and the indicator on the magsafe tip wouldnt even light up....
Chosen Solution The mic stopped working on my phone. I can’t use it on calls, record a voice note or a voice message on WhatsApp. Interestingly it doesn’t allow the option rather than record silence. If I connect a Bluetooth headset it works fine. I have bought and gone through the painful process of replacing the mic, speaker & charge port component thinking this would fix it, it didn’t. The phone works as before and still charges as normal....
Chosen Solution I recently purchased a new screen and digitizer for the iPad Mini 4 Wi-Fi/Cellular model A1550. The repair instructions were accurate, but…To remove the home button I was told to flip up the retaining flap and unplug the cable from the ZIF socket. All well and good but the replacement screen does not have a retaining flap and the socket is different. I can not proceed. Did I order/was I sent the wrong part?...
