Posts

Chosen Solution I have a LMXS30776S/00 with both the refrigerator and freezer not cooling properly. Checked compressor (appears to be working), fans working, cleaned coils, no help. Performed the voltage test on the main control board - CON201 (1&4 pin) after pressing the test switch. Voltage got up to ~50V Max. Left connector off and noticed LED blinking three times. Main Control Board? Thanks Brian Here are the top three, there are seven other causes if these are OK: Cause 1 Condenser Coils are Dirty The condenser coils are usually located under the refrigerator....

Chosen Solution Hi. Shaking gently my Iphone 4 i can hear a little sound as like a screw, which isnt fixed. Pressing the "sleep button" on top of the device and shaking it, the sound isnt hearable. Do you have an idea wherefrom this sound comes? Thanks. Gabriel Gabriel, I tested this with an iPhone 4, the sound that you are hearing when you shake your phone is in fact just the sleep button itself....

Chosen Solution I can no longer get Netflix on the TV . Can you retreive my initial password so that I can try a reset? When did you bought the TV ? Perhaps Netflix is updated and is not available anymore for your TV. If you have forgotten your PIN code, enter the master PIN code for your TV. You need to contact Sony regarding this. Also check the manual for your TV....

Chosen Solution In this model, the “Northbridge” chip is included in the processor chip? Your MacBook Pro uses a different architecture than using a North and South Bridge chips which is often used in desktop systems at the time. Here a more integrated solution was used based on a Platform Controller Hub (PCH) chip In your system it also included the dedicated GPU from NVIDIA (nForce PCH) And here’s a breakdown in a block diagram on the layout

Chosen Solution Hi everyone, I recently changed thermal paste on my MacBook. It ran for like 10 minutes, then it turned off. I don’t know if I mess something up. After that the system not able to turn on anymore and fan rev. I then unplugged the battery and tried to turn it on with charger. The system did not turn on but beep three times so I used heat gun to heat the RAM up....

Chosen Solution MacBook Pro 15" Core 2 Duo 2.4 GHz Model A1226 I replaced the display and the logic board of my MacBook Pro. Both were functioning fine before. After the reassembly the MacBook was working fine as well. So I took it with me to work with it but from now I wasn’t able to start it again. So I disassambled it again to the point of disconnecting all cables from the logic board....

Chosen Solution Yesterday, a friend at work and I were talking about his MacBook pro. He inquired about a few things including Windows 7 on it. I said I’d be happy to set up BootCamp for him. While at it, he said that he had purchased a Lion USB drive and asked if he should upgrade. I’ve done thousands of Windows installs and a few OSX ones so I said I’d do it for him....

Chosen Solution The mini just sits there with blank screen doesn’t respond to on button or middle go the lower panel button. It doesn’t register it is charging. Checked power supply. Any ideas? plug it in. if it is recognized by iTunes, then it is a backlight problem. repairable. jessa you can press the home button and power botton at the same time for 15s to see it works or not....

Chosen Solution Hello. When I changed my battery on iPhone 5s it started to do some blue screen stuff. Then I bought another battery from ebay, and after that my iPhone is stuck at boot loop. I almost gave up on my phone, then I saw very tinny resistor missing near charging connector. Image with marked resistor: Could this be problem? Anyone knows any data about this resistor and maybe where to get it?...

Chosen Solution Hi Everyone Never had this one before. Replaced a LCD on a customers iPhone 6S yesterday and they sent me the following this morning. Would appreciate some help in diagnosing & resolving the issue. “This morning I have made my first phone call since having the screen repaired and while on the call my phone (handsfree) it was muting/trying to connect to facetime and not allowing me to press any buttons to try and cancel....

Chosen Solution i just a removed the home button from a thoroughly shattered screen (hopefully to put in a new screen and preserve TouchID). the removal was no problem but i noticed the rubber o-ring fell on the table with a split in it so it wasn’t full circle. i’ve located a source for them on ebay, but what i can’t find is any instructions or videos on how to install it or where it goes on the home button assembly....

Chosen Solution Haven’t had an iPhone 8 with these symptoms. People can’t hear me clearly during phonecalls whether in handset or speakermode. Sounds like I am far away or voice is cut off so I sound like I’m stuttering. Using voice memo voice works perfectly. My colleague changed the charging dock and it was fine for a day and the problem returned. Audio IC related problem or something deeper perhaps. Any advice would be appreciated....

Chosen Solution Hi, I have an iPhone 6 that got very wet after being in the same bag as a drink bottle and it didn’t turn on. After opening it up I discovered that the home button connector had corrosion so after cleaning that up and leaving it in rice for 48 hours, the phone booted up just fine. It has been working perfectly for over a week, nothing wrong until today when it just suddenly died and gives no response to charging or a laptop....

Chosen Solution I just replaced the screen and digitizer on my iPhone SE with an iFixit replacement kit. Everything went smoothly and the screen works. However, the touch seems a bit slow and lagging at times. Sometimes it seems I have to tap something a couple times for it to recognize it. I don’t have any ghost touches anymore, which is what used to happen. Now, it is just a little slow to the touch....

Chosen Solution Hi, earlier today I dropped my iPhone SE on a tile floor on its back. It randomly rebooted and now it randomly reboots within 3 to 5 minutes of usage. Sometimes when it reboots, it has red and blue lines on the screen. I restarted the phone and reset the phone to factory settings, but nothing seems to work. I have it charging right now, and it’s stuck at 49% charge....

Chosen Solution I have tried multiple lcds and all have the same problem where the backlight will not turn on. the same lcds work perfect on a different logic board. this logic board has water damage but works fine except it will not make the backlight work. what part on the board needs replaced? anyone have a schematic? since some iPhones have the same problem, i would say that a coil is fried....

Chosen Solution I know you can on the 6 but I’ve read it’s fused to the digitizer in the 6s. Just looking for confirmation. The home button extension cable is together with the screen on the iPhone 6s. The home button itself is separate and removable though. You will have to replace the metal plate that has the flex extension in it. During screen removal, this cable is easy to stretch and subsequently damage....

Chosen Solution Hi! I’m getting quite high temps on my mac and was wondering if i can try apply liquid metal to the heatsink. I opened my macbook air and found a heatsink that looks to be made out of aluminum, but im not sure and can’t seem to find any information of whats it made of on google. https://i.imgur.com/a7vwian.jpg Update (04/15/2019) Okay so no way to use liquid metal? Is arcric or grizzly paste best?...

Chosen Solution So for about a month ago my iPhone stopped connecting to my service provider. It sits at no service and goes back and forth between searching. I bought a new SIM card and tried all the tricks I could find on the internet but they didn’t work. Everything else on the phone is fully functional, so I was just wondering could it be fixed? I was told by the last tech I spoke with it was the antenna inside the phone that was broken....

Chosen Solution I have an iPhone 5 that was “liquid” damaged and am trying to see if I can get it working enough to get the photos off it. It currently powers on for about 2 seconds and then loops. I removed removed the logic board and EMI shields with the intention of cleaning, but found large parts of the board covered in a hard, black, wax like substance. It’s deep enough to almost cover some SMD caps/resistors and surrounds a number of the chips....