Chosen Solution Where can I obtain a 36 volt power supply for my Kodak ESP3? Hi, Here is a link to just one supplier. http://www.accessoriesbank.com/36v-kodak… There are other suppliers who may suit you better. Just go online and search for Kodak ESP 3 power adapter to get results.
Chosen Solution hi any advice on replacing my screen please my laptop is ASUS X540SA - XX174T thankyou Hi @carlos_76 , Here’s a link to a video that shows how to remove the LCD panel from your laptop. Here’s a link to a supplier of replacement LCD panels for your laptop. (click on the Display check box on the webpage) It is only shown to give an idea of the cost of the part....
Chosen Solution After falling a glass of water, I cleaned the entire motherboard with isopropyl alcohol and everything works fine except the backlight and the LED screen, ie pictures but you can see this as having no brightness. Know if there is a fuse you can check. You can see on the picture that if you approach a light you can see the contents of the screen. Can anyone give me some help?...
Chosen Solution I have replaced my LCD screen and reattached the entire front panel and reconnected every cable. But now when it works, the entire left column of apps on the left side will not respond. Everything else works, and the right side responds also to touch, but the 1st line of apps on the left side is unresponsive. Is it possible to fix this problem? Benjamin Lee, I would recheck my work....
Chosen Solution MY LG refrigerator dispenses water into the ice tray, freezes the ice and then tilts the tray but does not complete the process of dumping the ice. Eventually it gives me an Error 15 and when I do a diagnostics test on it shows an Error IS. I have changed out the ice maker. I have changed the main board on the fridge I have changed the board that is located on the top of the left fridge door ( sub PCB board ) I did an ohm test on the connector 11 & 12 of the ice sensor cable and those are showing normal....
Chosen Solution Fitted a new battery and macbook powered on fine. however I did not notice that it was not charging until it became flat. On investigation I found that the MagSafe connector on the laptop had shorted. I fitted a new one but the laptop will not boot with the battery installed. I can boot without the battery and every thing is fine. My question is how can I revive this new battery?...
Chosen Solution Yesterday I restarted my Macbook Pro to find that the LCD display wasn’t working – there’s not even a dim picture, it’s just completely black, as if the display was asleep. Up until that point, it had been functioning completely normally, no visual glitches or issues – the display simply didn’t turn back on after restart. When hooked up to an external display, the computer is still fully functioning....
Chosen Solution Prior to failing to boot the laptop the screen would begin flashing and lock-up. I would reboot and every thing was find for a while. Then while working my screen started flashing again and the machine again locked up. Now when I turn on the machine it chimes, the apple logo appears and the hard drive spins. However after about 30 seconds of trying to boot the screen darkens a little and a message appears: “You need to restart your computer....
Chosen Solution Two days ago I wanted to continue with my video project on my MacBook Pro. I opened it (I don’t shut it down) and it was off. I thought maybe the battery was dead and I didn’t charge it. So, when I put my MacBook in the charger and click the on button it went on for 5 sec and then turned off. I pushed the button again and now I could login I looked at the battery it was still 80% so I thought that’s odd....
Chosen Solution Hi all, My Macbook Air no longer charges when connected to my Thunderbolt display. The led on the magsafe connector is blinking fast (green). Question: what could be the problem? Tried: cleaning the connectors / reset PRAM / reset SMC / disconnect power for long period (hours). All the best from Holland, Pieter We don’t have a cord or power supply replacement guide. If the cord looks OK I would suspect the power supply is having problems....
Chosen Solution I have an older iPhone 6. The frame of the phone has been bent and touch function sometimes works. I am not sure if it is a Touch IC problem as there is no grey bar at the top of the screen. The display does not flicker and it is just the touch that stops working. Also, whenever I apply pressure to the touch ic area, the touch starts glitching out....
Chosen Solution Hi, I have a maytag bravos quiet series 400 washer. And when it get’s to the spin cycle, it looks like it can’t get going into the spin cycle. It attempts to rotate clockwise (moves about an inch or less), then stops for a second, then it tries to rotate counter-clockwise (moves less than an inch), and repeats over and over. Eventually it shows an SD error after many minutes....
Chosen Solution Disclaimer: this question might show a complete lack of understanding of the finesse of electronics. My iPhone 4S’ charging circuit is not working properly, so I am looking at convenient ways of charging the battery outside of the phone. I’ve found a circuit diagram posted here by oldturkey03, and I will give that a shot. Then I had another thought; I do have old li-ion chargers, for digital cameras and such....
Chosen Solution I’m trying to connect to a WiFi network via Settings » WiFi on my iPhone 8 and it only shows 5GHz networks and no other networks including Personal Hotspots (I did a research and found out that Personal Hotspot works at 2.4GHz). WiFi works great on 5GHz networks, but it’s very difficult to find one in my area and the phone becomes pretty much unusable. Other devices like a MacBook Pro and an iPhone 6, 6S, 7 - all detect lots of 2....
Chosen Solution Hi, Hope you can help.. My friend had a iPhone 3G that was working, but had a cracked digitizer and no power button, but it did still work. He asked me to replace the digitizer and the power button, so while I was at it I thought I would replace the back to the phone too. I also replaced the battery. However, I have replaced everything and put it all back together and now the display doesn’t work (which it did before)....
Chosen Solution Since I replaced the camera lense. The camera has not been able to autofocus or Manual focus on up close photo shot ( look at the image ). I would like to know if there is anyway to repair the focus on the camera. Physical repair and not software. Since I restored to a factory set, I don’t think it’s a software issue. Things I have tried to repair....
Chosen Solution the gold antenna next to battery connector has been snapped off (not by me) just wondering if there is a fix for this as the rest of the phone is working now! resoldered to small square
Chosen Solution I dropped my camera real bad and half the screen is busted, its black with green lines and the other half is normal. is there anyway i can replace the main screen? My lens are also pretty messed up is there any way i can replace that, as well as the little flap that holds the battery in place. Hi, Here’s a link to the ifixit GoPro Hero4 Black LCD Screen Replacement guide....
Chosen Solution Is it possible to resoldering keyboard blacklight connector? Hi everyone, I just recently bought a macbook with a broken blacklight keyboard connector. And i thinking to let some one soldering this thing so i can get my keyboard blacklight on, and be able to use the sleep sensor on this machine. I was just wondering if there are somebody has previously did it or fix it could give me some of the experience?...
Chosen Solution My LG Nexus 5 was shattered completely due to fall from height 1.5 years back. Recently, I plugged it to a charger and it could switch on but nothing was visible due to broken screen except for background white light. Hence, I bought the LCD, digitizer, Frame assembly from Aliexpress.com and decided to reassemble it myself. When I opened up its components, few pieces fell off from the motherboard and one piece from rear-facing camera was missing and 3G antenna wire has broken off from its connector....
