Posts

Chosen Solution Bought a replacement brake fluid reservoir…How do you remove the reservoir from the master cylinder on a 2008 Jeep Wrangler? @tammyup from the service manual:

Chosen Solution LG Leon MS345 no service after unlock Hello, i have one LG Leon from MetroPCs, I unlocked with the App Device Unlock and everything was fine until the next day that i could not make call and it shows me Emergency calls only. i´ve been trying and the phone not register in the network. Please if someone has the same problem and know how to fix this, i have restored and reflash the device but still the same problem ....

Chosen Solution How to change the bulbs in front headlights? First remove the two bolts that hold the intake in place. Then move the intake off to the side. Then you have to pull back the rubber hood from the light. After that you use a pair of pliers to unhook a clip that holds the bulb in the mount. Here’s where to get some bulbs: http://www.partsgeek.com/gbproducts/WC/1…

Chosen Solution I have a pod x3 live and i am wondering how well this would work as an audio interface when recording with garageband 11. my concerns are compatability, latency, and the overall sound quality of the recording. 1:does a firewire connection yield superior sound quality? 2: what is the most important component of a home studio that yields the best sounding recording? (other than the musicians). Is it the DAW, interface, or plug-ins?...

Chosen Solution So… I bought a 2011 MacBook Pro on eBay that said the logic board was failed based on advice from a buddy. I’m a novice, so please forgive me. I did the typical “put logic board in the oven” trick. I put a new SSD in it too. After a bunch of messing around, I was able to format the drive and install High Sierra using a bootable USB file I found from my windows....

Chosen Solution Hi I am looking for a replacement for my MacBook keyboard. my MacBook model is A1278 and my keyboard is ISO Arabic. Your best bet on this may be : Jon Ridley @thebookyard They specialize in Mac keyboards. You can find them here: http://www.thebookyard.com UPDATE Look for part # A661-5561 Here’s one: http://www.ebay.com/itm/MacBook-Pro-13-A… At $40 this is probably the best way to go. The main detail you need to confirm with the A1278 model, is which keycap type you have....

Chosen Solution How do you replace the power supply in a Mac Pro? With great difficulty and the original installation disks to be able to run the fans syncing software. First, let’s see if you need to do this. What are your symptoms? What is your EXACT model (information is found after removing door and looking on the bottom of the opening.

Chosen Solution My son was using his MacBook Pro 15 early 2011 when the machine shut off on its own. He thought the battery may have died so he attached his charger. The laptop chimes but does not start up. Disconnected battery - attached charger and the sleep light comes on and optical drive spins then the machine shuts off. When you hit the power button after this the sleep light comes on, blinks 6 times, optical drive spins, chimes and then powers off....

Chosen Solution Hello everybody, I am having a very weird problem with my MacBook Pro 15’’ Mid 2009 model. I recently damaged my hard drive, so I decided to buy a new one, which is exactly the same model as the one that I had. A Seagate ST9500420AS 500 GB 7,200 rpm. Now the thing is that, although my previous drive is damaged, it can still be recognized by the disk utility when I boot from the Snow Leopard Installation DVD....

Chosen Solution Hi, this is a mid 2010 macbook pro. when temperature goes up, its screen start having problems like this. there are horizontal lines on the screen. sometimes it stop responding. hope get some useful advice here, thx a lot! i dont know how to add pics, here is a link https://photos-3.dropbox.com/t/0/AAC2Zfu… Hi Luyao, The issue you are describing could be related to either the LCD or to the video chip....

Chosen Solution i just received a 2011 mbp13 2.3 i5 model, exhibiting no power whatsoever. not even magsafe when connected. i pulled the logic board, cleaned thoroughly and added a new DC in board. testing the new DC in board outside the chassis, i got (at first dim, and then full) green LED at the magsafe. i plugged in the fan, and sure enough the mac was powered on. i pulled the plug, reassembled the laptop, and there’s no power whatsoever again....

Chosen Solution Quite an expensive Voltmeter device , did this from day one OL means ‘over load’ but it isn’t even connected to anything i suspect it is faulty but wanted to find out if anyone else has experienced this and maybe it’s simple This is a common misunderstanding but OL means open line. It means that what is being measured is not making it’s way from black probe to red probe....

Chosen Solution I didn’t have my PC so I used this one and first it doesn’t show up I try to eject it and it doesn’t work. How do I get the MicroSD card out of the slot?? Hi @howtofixthings8 You will have to open the laptop and try to gently push the SD card back out from the rear of the card reader. Here’s the owner manual for the laptop....

Chosen Solution Hello! My iPhone 8 has stopped working after I charged it, the screen was black and the phone was very hot, I tried ‘hard reset’ and charge it after my battery was drained. However, it didn’t work at all (not getting even warm from charging). I ordered a new battery and a board to charge the battery. The old battery was dead, I couldn’t charge it even with the board....

Chosen Solution My iPhone X suddenly turned off and wont reboot unless I update it using iTunes or restore it, and every time I try to update it the phone unplugs it self from the PC several times and then I get this message “iphone could not be updated error 4013” The problem was in the Face ID, I disconnected the face ID from the phone and it works, I can’t use Face ID nor the front speaker for phone calls, but the phone worked and the data is not lost and everything went back to normal, and now I can at least use and back up my...

Chosen Solution Hey, i have a iPhone 6 with ios 10.1.1 the Device come with a Broke Display, i Change it and the new got broked. i Replace again a new Display. but now my iDevice is Turning on. and iTunes ask for the PinCode. but i have no Picture and No Vibration on this Device. i dont know if it the Touch IC or Backlight Problem. i dont want to Restore my Device on New iOS… :)...

Chosen Solution Hi, I appreciate any help that I can get. I have recently refurbished an iPhone XS for a customer which included the back panel. Everything seemed to be fine until the customer got back to me saying that when paying at a supermarket they were not able to pay with Apple pay. To me, this sounds like an NFC problem however I don’t know how to fix this. Is it the wireless charging coil that has the NFC or is it on the motherboard?...

Chosen Solution Hello, I have an ipod touch 3rd gen. and the volume icon remains on the screen all the time. Also the volume top button will turn on and off the device and the bottom one does not work at all. Has anyone got the answer for me I hope so. Thanks for reading this, Marianne I will chime in without advertising a buisness try resetting the iPod,hold the home and power button down at the same time,the iPod will reset and if it silll happens,chances are there is dirt in the volume jack causing this,you can certanly try taking the iPod apart and cleaning out any dirt and gook by and in it if it comes apart,otherwise,you need a whole new headphone assembly...

Chosen Solution I need some help, the other day my ipod was fine and than all of a sudden it shut down on me. I thought it might have been the battery life but the battery is fine. The problem seems to be that every time I try to turn it on it just stays on the apple logo with black screen for a few minutes and turns off. Every time I turn it on it that happens, so I tried resetting it to factory setting but when I connect it to my computer it just turns on and never syncs to my computer....

Chosen Solution Hi, the title may be wrong a little bit, but it’s true. To give as much information as possible i will tell the full story. Yesterday i got my ipod in the mail, and it had a few scratches but it was working amazing. Then at the end of the day i was working on a dock for it and i had my gloves on. When i reached for it it fell out of my hands but only on the desk, not the floor, because i kind of slowed it or catched it when it was flying....