Chosen Solution My “K” key will type a “k” with very little pressure. I’m accidentally typing k’s all over the place because I barely graze it. There might be something under the k key cap that is pushing down on the button. I would first use some pressurized air near the key and see if that works. Otherwise you can take the key cap off and see if anything is under it and if so remove it....
Chosen Solution One day I was working on my latitude D620 and all of a sudden it just shut off. I tried restarting it, but when turning it on I only got the power icon light to turn on for about 3 second and then the light went away. Also when I try to turn it on I do not get a fan sound or a hard drive sound. It seems to me that there is no power going to the drive or fan....
Chosen Solution Hi guys I have an apple cinema display that is not turning on. The usb and everything else works but the display itself is not working. I have checked the technician guide and all the test points on the logic board are good. So my thoughts are the lcd panel itself. My macbook does not detect the display and I can’t see an image when I use a flashlight....
Chosen Solution After switch on my iphone 5c 32Gb , some faded thin black lines are appearing in left side of the screen and the touch response in left area is not working , whether right side of screen is working properly. Please suggest the solution. You most likely have a defective screen assembly. You can replace it yourself by following this guide. Update (08/24/2017) I have already tried by de-assembled the LCD screen and cleaned the all port and again assembled it properly ....
Chosen Solution Lenovo E530 will not go past start up screen and I need it fixed. It has windows 7 and I think it tried to update windows 10 during the night. It hasn’t worked since. It will give options to go into safe mode , safe mode command startup or regular windows startup. Any that is chosen will boot up got start up screen and then to a blank screen with only curser showing....
Chosen Solution why does horizontal lines occur in the bottom of the sreen sandhya sandhya connect an external monitor to your computer. If that monitor does not show those lines you know that it is your computers screen that has failed. If it does show those lines you are having issues with the video circuitry on your computers motherboard. Let us know what you find. Damage to the screen, Failing graphics card or loose internal video cable....
Chosen Solution Hey guys. I have an iPhone XR that I am working on that suffers from liquid damage and currently does not power on or charge properly. I have ruled out a parts problem by swapping out the lightning dock charging flex cable and a new battery to no effect. The logic board has been ultrasonic cleaned, as there was visible corrosion on the board.I’ve taken some measurements and I am leaning on something wrong with BB_PMU or BB itself, but wanted some other opinions....
Chosen Solution My Ecco television is one of the old models and not the lcd screen. It takes long about 4 to 5 minutes to power on, and plays well for a few minutes then starts flickering and eventually shows mixed shaking horizontal lines until it powers off again on its own. A friend who is an electrician told me its possible it has to do with a bad capacitor but my problem is I don’t know anything about these things....
Chosen Solution I’ve been looking for a replacement ac adapter online for hours. I can’t find any that are specific to the LeapTV system. Could you please point me in the right direction? Hi @radiatehope , Here is a link to one supplier. It is not a recommendation to use them. It is shown to give an idea of the price. There are others online, especially on Ebay. Just search Ebay for LeapFrog Leap TV adapter to get results....
Chosen Solution What do I need to fix in order to stop my PS3 from shutting down after 2 hours of gameplay? The fan speeds up about 5 notches within a minute then sounds like a hoover within half hour, eventually shutting down. It doesn’t have the YLOD; I can turn it back on and carry on playing. So, what do I need to do before it eventually blows up?...
Chosen Solution Unit is plugged in - green light showed battery is fully charged. no response to a power on function when the power button is pressed. Memory has been removed and swapped and no change in condition. Battery has been romoved and reconnected and no change in condition. Ran several restart keyboard actions and no change in condition. help! I suspected that the C2D was the model in question. If you experienced in the past difficulties in starting up the machine, needing a few attempts to start especially in the cold, it’s almost sure it’s a logic board issue....
Chosen Solution Interior of dryer gets very hot after a few minutes running. Clothing is very hot to the touch. Cause 1 Heating Element The heating element warms the air before the air enters the dryer drum. If the element is partially shorted out, it may produce heat continuously, even if the dryer has reached the proper temperature. When this happens, the dryer gets too hot. To determine if the heating element is at fault, use a multimeter to test each terminal for continuity to the case....
Chosen Solution The motherboard on my imac went bad so I purchased a complete motherboard on ebay. Same model but an i7 processor rather than the i5. Except that when I got it I found out its EFI locked and it’s a mid 2011 so the ram trick won’t work. I have read through how to reprogram or clear the password on the chip but thinking it will be easier to just swap the unlocked chip on my old board to the new....
Chosen Solution I am looking for a link to most revelant info/describe all aspects of changing out broken screen on iPad A 1395. Thanks in advance! I would recommend this guide. Read through it first to get comfortable and then order the parts you need and proceed carefully.
Chosen Solution I have a craftsman zero turn 26hp 50 deck but my mower deck will not lower or raise when i push the switch in the users manual on page 16 is the installation of the mower deck shown - maybe you should check those steps if you don’t have it - here is a download adress - it was the first one i’ve found Same thing here! Called Sears, and they sent a repair man....
Chosen Solution Hello all, I have a iPhone 7 and would like to implement wireless charging by replacing the back housing. Is it possible to buy an iPhone 8 housing with Qi pad on EBay and build rest of the phone using iPhone 7 parts?? Both phones are comparable in size so will this work? Is it compatible? thanks Unfortunately they are not compatible. They are not the same size, they have a different camera layout and there would be nowhere on the iPhone 7 board to connect the Qi charging pad....
Chosen Solution After I installed a new battery from ifixit.com to fix the error 29 during a firmware update (which worked perfectly fine with the new battery), my phone just randomly turns off and without a charger I can rarely restart it. At first, even my time was set back to the first of January in 1969 every time this happend but when i set it to “set automatically” it seemed to have fixed this part of the problem....
Chosen Solution intermittently the Mazda B2600I pickup will start to loose power and when we accelerates it looses all power and back fires. If I shut the engine off for just a couple of min. the problem goes away untill who knows when. Thank you. Please responde back mags4gsus@cox net To answer your question, the fuel pump is located inside the fuel tank, attached to the tank sending unit assembly. 1....
Chosen Solution Help! I accidentally just deleted all of the pictures on my Smartwatch DX. How can I recover these photos? Unfortunately, there is only one way, which is using a third party software that can recover pictures. However, we don’t recommend these types of software. Use at your own risk.
Chosen Solution My kuerig is only brewing partial cups, not even half. It was given to me by a friend whom got a new one…. I have descaled it, I have cleaned the needles, I have checked the reservoir and all seems to be good. But when it brews there is drips of water coming out of the over flow and it stops brewing, but when I cover the white soft plastic it will begin to fill the cup again....
