Chosen Solution Hi. I’m new to this site, so hopefully I’ve posted in the right section aha. TL;DR - My iPhone will literally die unless there’s charge going to the iPhone. Once the charger’s disconnected from the iPhone, the phone will die. Once I’m charging the iPhone, it will begin to show the boot logo but in a loop over and over (till about 5-10 minutes have passed) then I can access the phone....
Chosen Solution My Iphone 5 has been charging for a day but it is still stucked in the battery logo. What should I do?? The problem is you don’t really know if the battery is charging or not. Your battery could be at the end of its life. To be certain, use a battery utility, such as coconutBattery (for Mac) or 3uTools (for Windows). It will tell you what the health of the battery is....
Chosen Solution I got this problem out of blue, iPhone was working and then it turned off, no wheel, I thought it could be low battery then I tried to charge, It turned on showing Apple logo for like 1 or 2 seconds and then backlight black, and when I removed charger it turned off immediately. I brought it into a friend who fix iPhones and he tried changing display and battery, no use, he told me to try to format it, and I tried, i connected it to my mac but it does recognize, it only recognizes when I put it in recovery mode, mode in which in this case shows no response on the screen, the mac tries the process of recovering, but it gives me the 4005 error....
Chosen Solution I was trying to downgrade from the iOS 13 beta to iOS 12.4.1 but during the restore, there was an error and now it’s stuck in recovery mode no matter what I do. Whenever I try again I get the same “unexpected error (9)”. Everything is updated, I tried using a different cable, and turning off my antivirus (all things that came up when i looked up this problem)....
Chosen Solution Hello, recently my mate brought me his iphone 6 which after replacing screen in no named mobile fix store with unsticked screen from the frame that I was able to see inside the phone throught this “unsticky screen”. I told him that is not big problem, i can put adhesive there and stick it in. So i did it, I opened the phone, uplugg battery then screen, put adhesive under screen and then made everything together....
Chosen Solution Hey y’all, my iPhone x recently got stuck in a reboot loop. I let it do its thing until the battery died, plugged it in and it powered on. My phone behaved normally for about 20 minutes, then back to reboot loop. I tried this again, and after researching I decided to quickly go to settings and do an iOS update. Which worked, for about three days. I’ve connected it to iTunes and recieved the notification that something was wrong and I needed to update or restpre....
Chosen Solution Is it possible to install the ram Kingston SODIMM DDR3L-1600 16384MB PC3-12800 (Kit of 2x8192MB) (HX316LS9IBK2/16)? Your system was designed to use 1333 MHz PC3-10600 DDR3 SDRAM. While time has marched on you can use DDR3L modules as they will run in both low & standard voltage based systems. At the time Apple designed and built this series larger RAM modules just weren’t available for them to test out which is why Apple states in there MacBook Pro: How to remove or install memory guide a limit of 8 GB....
Chosen Solution Apple Hardware Test returns an error for the video card. Yes, the video card is integrated into the logic board. So if the video card fails, then you have to replace the whole logic board. This is a possible Nvidia GPU Apple recall. Please hook it up to an external monitor to test the Graphics card and let us know the results. Sorry for not seeing your question earlier, it got by me....
Chosen Solution My supplier said there is a shortage of iPhone 5s/5c/5 screens and he is having a hard time finding the good quality ones. The price increases $10 each for his current supply. Anybody heard of this? Here’s whats most likely really happening. The parts in the after market are not all manufactured by LG and Sharp like the Chinese Distributors would like to let you believe. They are largely counterfeits....
Chosen Solution I Dont have an i opener and i was wondering if i could use anything else that does the same exact thing as the iOpener. Thanks A heating pad or a heat gun. :) I know this is a bit late ;>)… If you are a shop and will be doing iPad repairs on a regular basis, then a heated mat station like this is the preferred solution. However, if this is for a one-off, the these “Magic Bags” work really well....
Chosen Solution I dropped this phone from about one and a half feet up and now there are three clusters of rainbow pixels. I have tried JScreenFix for over 15 minutes but that didnt work. The phone is brand new with a screen protecter and an OtterBox case. No. You’ll need to get the screen replaced, it is physically damaged.
Chosen Solution Hi all! You’ll notice a major backlight problem in the image attached. I know it’s not a board issue because when replaced with a good screen there is no issue. I have several of these screens and considering how expensive iPad Air 2 screens are I would like to repair the screens. Does anyone have air 2 screen schematic? or has anyone had luck repairing a similar issue? Seems so wasteful to just toss them…...
Chosen Solution Having followed the excellent guide to install dual HDD in my 24" iMac, everything works except when I try to use my internal iSight camera it says: “camera not connected.” It IS listed as a USB device under system profiler. I have tried: Reset PRAMDisable SIP Any ideas before I disassemble and check cables etc.? No, proceed straight into disassemble the machine and check the cables.
Chosen Solution Android tablet keeps resetting the reset screen I tried factory reset and nothing… PLEASE HELP Try disconnecting the battery for a few minutes then reconnect and reboot this video will help open the tablet and disconnecting the battery . he shows disconnecting the battery at 1:11 of the video https://www.youtube.com/watch?v=KPuUdZQW… Hope this helps
Chosen Solution Ive tried to solder this battery connector on aN IPhone 4 and everything went pretty easy. -I just cleaned al the solder with a solder wick. -Put some flux and solder on the two anchor pads(the two located outside) -Took a piece of Kaptons tape and cover the connector except the two anchor pins. Don’t cut the tape too short so that yoy can use it to help you align it on place -Applied some heat at about 1 inch away from it....
Chosen Solution The highest system this machine will take is El Capitan Pre-Installed MacOS:X 10.5.8Maximum MacOS:X 10.11.x* https://everymac.com/systems/apple/imac/… UPDATE 3/2022 DosDude has now come out with work arounds and patches. which allow for system upgrades to unsupported Macs. I have had fair luck using them. That’s wrong that’s not what Apple said Apple said it could be updated to Mojave
Chosen Solution I can’t set the oven temperature below 350F. When I press the Bake button the 350 temp comes up and pressing the “down” arrow does nothing. I can increase the temperature but can’t lower it. Any suggestions? Hi @dverve, Does the down arrow work OK when used for other functions e.g. time, Broil Lo? If not then it may be a faulty down button or a problem in the control board part #318296824....
Chosen Solution When I plug in my laptop in the power button and the caps lock button light up for a second or 2 then go out. Then the power button and the wifi and the mute button come on for a second or 2 then go out. This happens twice then the laptop becomes unresponsive. I have replaced the power supply but it still acts the same. I have tried the 30 second power button reset and no luck....
Chosen Solution hi there, can the RAM on the MacBook Air 2010 13 in be upgraded? are there any vendors which make these memory chips? No, the ram on every iteration of MacBook Air is soldered onto the logic board making it impossible to upgrade. If you want to upgrade all you can do is get a new logic board with more ram. Hope this Helps
Chosen Solution Recently this macbook started thinking ALT / Option key is always pressed and cant write properly, did try already SMC Reset, changing to new keyboard and just today swapping to “new” logic board from ebay and same.. its failling even from OSx Install terminal (takes some time to start failing like 5-10 mins) any idea why its failling?? (im out of ideas after new keyboard / logic board..)...
